Gray Tamper-Void Permanent Poly Labels
#102351 - Matte Permanent Tamper Evident Labels
This Tamper Evident laser material has a dull silver look to it and a VOID self adhesive, that if removed after application leaves a VOID pattern indicating tampering. Can be printed on a Desktop Black and White or Color Laser Printer (For HP: Tuff Paper Setting). This material may be applied to metal, glass, or polycarbonate plastics and left to dwell for the VOID to show when the label is partially or fully removed.
The adhesive is a clear acrylic adaptable to many surfaces with a minimum application temperature of 50°F and a service range of -40°F to 302°F. On rough surfaces or low energy surfaces, 102351 shows an excellent random tamper proof pattern.
Short Run
| Sheet Ct. | Price Per Sheet | ||
|---|---|---|---|
| 8.5″ × 11″ | 8.5″ × 14″ | 8.5″ × 17″ | |
| 10 | $9.29 | $11.85 | $14.58 |
| 25 | $6.52 | $8.16 | $10.07 |
| 50 | $5.52 | $6.93 | $8.53 |
| 100 | $3.98 | $5.04 | $6.20 |
| 250 | $3.17 | $3.93 | $4.88 |
| 500 | $3.04 | $3.76 | $4.70 |
Long Run
| Sheet Ct. | Price Per Sheet |
|---|---|
| 8.5″ × 11″ | |
| 500 | $2.60 |
| 1000 | $2.18 |
| 2000 | $2.06 |
| 5000 | $1.88 |
| 10000 | $1.81 |
Let us print for you! Full Color Printing available.
Specifications
Description:
This is a matte top-coated laser printable tamper evident metalized silver void polyester film. It is coated with a permanent, pressure sensitive acrylic adhesive and backed with a backside-printable, two sided, poly coated, tissue backed release liner. The tamper evident feature of this product becomes permanently nonfunctional after exposure to 104°F (40°C) temperature. This product is UL recognized for indoor/outdoor use with occasional exposure to lubricating oil and water.
Facestock
- Metalized silver polyester film
- Caliper: 2.4 mils
Adhesive:
- Emulsion acrylic permanent
- Caliper: 1.0 to 1.1 mils
- Min. application temp: 50°F
- Indirect Food: No
- Min. Service Temp: -40°F
- Direct Food: No
- Max. service temp: 302°F
Note: For best bonding conditions, application surface should be at room temperature or higher. Low temperature surfaces, below 50°F can cause the adhesive to become so firm that it will not develop maximum contact with the substrate. Higher initial bonds can be achieved through increased rubdown pressure. In order to get a true measure of the adhesive's effectiveness, the label should be applied and allowed to bond a minimum of 24 hours prior to evaluation.
Liner:
- Bleached 5.7 mil kraft paper (lay-flat) liner that has been poly coated two sides to give a controlled release.
- Caliper: 5.7 mils
- Weight: NA
- Basis weight: NA
The above are typical technical values and are given in good faith based upon our most up to date knowledge and experience. As the products are used outside our control we cannot take responsibility for any damage that may be caused using the product. In every case, user shall determine before using any product in full-scale production, or in any way, whether such product is suitable for user's intended use for their particular purpose under their own operating conditions.
Availability
This product is stocked and can be shipped in as little as 24 hours. Please contact us for more information.